Base para Caixa de Bateria 48V 16S DIY | Plataforma com Rodízios com Trava, Estoque UE

Rodas para caixa de bateria para sua caixa de bateria DIY 48V 16S — uma base de aço com rodízios com trava que permite mover um pack finalizado de 120kg manualmente em vez de levantá-lo. Fixe-a sob a caixa, instale suas células e mova tudo para o lugar.

O Que o Kit de Rodas para Caixa de Bateria Inclui

Esta listagem é a base com rodízios apenas. . Não é uma bateria, não é uma caixa e não é um BMS.

Para Quais Caixas de Bateria Estas Rodas Servem

A base é projetada para caixas DIY 48V / 16S feitas para packs LiFePO4 acima de 280Ah — as caixas que vendemos nesta loja: o Kit de Caixa de Bateria DIY 15kWh A1, o Kit de Caixa de Bateria Empilhável 280Ah A2, a Caixa DIY Horizontal 320Ah A3 e o Kit de Caixa de Bateria Vertical V3.

Caixas de outros fornecedores podem usar um padrão de parafusos diferente. Envie-nos a caixa que você possui e confirmaremos a compatibilidade antes da compra.

Quanto Pesa um Pack 16S Completo?

Esta é a razão da existência da base. Um pack 16S completo é muito mais pesado do que a maioria dos construtores espera:

Cell weights vary by brand — EVE LF280K is around 5.4kg per cell, and 314Ah cells are a little heavier. Either way you are handling well over 100kg once the pack is assembled, and that is not something you lift onto a shelf.

Build the pack on the base, or fit the base before you install the cells. Both work; the second is easier on your back.

Choosing Casters: Load, Floors and Brakes

Load rating. Four casters rated 75kg each carry 300kg, which leaves comfortable headroom for a 120kg pack. [Confirm your base’s caster rating.] Brakes matter more than wheels — a locking caster keeps the pack from creeping while you torque terminals. Floor type: hard floors roll easily, carpet and uneven concrete need larger diameter wheels. Cable strain: never roll the pack by pulling on DC cables; move it by the enclosure handles and re-check terminal torque afterwards. Clearance: leave room behind the pack for communication cables and any ventilation gap.

Fitting the Rolling Base: 4 Steps

1. Empty the box. Fit the base before the cells go in — a bare enclosure is around 30kg and easy to turn over.
2. Line up the mounting holes and hand-tighten the bolts first.
3. Torque in a cross pattern so the base seats evenly and does not distort the enclosure.
4. Fit the casters, lock the brakes, then build your pack. Re-check every bolt after the first move.

Technical Specifications

Perguntas Frequentes

Does this include the battery box? No. This listing is the rolling base only — the enclosure, BMS, LCD and cells are sold separately.

Can I fit the base after building the pack? You can, but it is much harder. A finished 16S pack weighs around 118kg; fitting the base while the enclosure is empty is far safer.

Will the wheels fit a box from another brand? The bolt pattern is matched to our A1, A2, A3 and V3 enclosures. Send us your box dimensions and we will confirm.

Do the casters have brakes? [Confirm with the supplier, then state it plainly.]

How much weight can the base carry? [Confirm the rated load, then publish it — this is the question every buyer asks.]

Build Your Box: Related Kits and Cells

Pair the rolling base with a matching enclosure — the A3 box (with JK V19 200A BMS or as an empty enclosure), the A2 280Ah Stackable Kit, the V3 Vertical Kit, or the A1 15kWh Kit. Cells in 280Ah, 314Ah and 320Ah are available in the same warehouse.